Arcteq AQ-G215 Скачать руководство пользователя страница 60

Страница: 60 / 458

Figure. 5.2.1 - 60. Residual I02 CT scaling (sensitive).

Displaying the scaling

Depending on whether the scaling was done based on the CT primary values or the protected object's

nominal current, the measurements are displayed slightly differently. The first of the two images shows

how the measurements are displayed when the CT primary values are the basis for the scaling; the

second shows them when the protected object's nominal current is the basis for the scaling.

Figure. 5.2.1 - 61. Scalings display (based on the CT nominal).

Figure. 5.2.1 - 62. Scalings display (based on the protected object's nominal current).

As the images above show, the scaling selection does not affect how primary and secondary currents

are displayed (as actual values). The only effect is that the per-unit system in the relay is scaled either

to the CT nominal or to the object nominal, making the settings input straightforward.

Q-G215

-G215

Instruction manual

Version: 2.04

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды