Arcteq AQ-G215 Скачать руководство пользователя страница 333

Страница: 333 / 458

Name

Range

Step

Default

Description

Curve1...4 input

minimum

-1 000

000.00...1 000

000.00

0.00001 0

Defines the minimum input of the curve. If input is below the

set limit, "ASC1...4 input out of range" is activated.

Curve 1...4 input

-1 000

000.00...1 000

000.00

0.00001 -

Displays the input measurement received by the curve.

Curve1...4 input

maximum

-1 000

000.00...1 000

000.00

0.00001 0

Defines the maximum input of the curve. If input is above the

set limit, "ASC1...4 input out of range" is activated.

Curve1...4 output

-1 000

000.00...1 000

000.00

0.00001 -

Displays the output of the curve.

The input signal filter (see the image below) calculates the average of received signals according to the

set time constant. This is why rapid changes and disturbances (such as fast spikes) are smothered.

The Nyquist rate states that the filter time constant must be at least double the period time of the

disturbance process signal. For example, the value for the filter time constant is 2 seconds for a 1

second period time of a disturbance oscillation.

When the curve signal is out of range, it activates the "ASC1...4 input out of range" signal, which can

be used inside logic or with other relay functions. The signal can be assigned directly to an output relay

or to an LED in the I/O matrix. The "Out of range" signal is activated, when the measured signal falls

below the set input minimum limit, or when it exceeds the input maximum limit. The "Out of range"

signal is very useful when e.g. a 4…20 mA input signal is used (see the image below).

Q-G215

-G215

Instruction manual

Version: 2.04

332

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды