Arcteq AQ-G215 Скачать руководство пользователя страница 198

Страница: 198 / 458

The function outputs the START, TRIP and BLOCKED signals which can be used for direct I/O

controlling and user logic programming. The function generates general time-stamped ON/OFF events

to the common event buffer from each of the three (3) output signals. In the instant operating mode the

function outputs START and TRIP events simultaneously with an equivalent time stamp. The time stamp

resolution is 1 ms. The function also a resettable cumulative counter for the START, TRIP and

BLOCKED events.

The following figure presents a simplified function block diagram of the power protection function.

Figure. 5.3.15 - 138. Simplified function block diagram of the power protection function.

Measured input

The function block uses three-phase power values (active, reactive, or apparent). A -20 ms averaged

value is used for pre-fault data registering. The used power measurement value depends on user input.

If the protection relay has more than one CT module, the

Measured side parameter determines which

current measurement is used for power measurement.

Table. 5.3.15 - 134. Measurement inputs of the power protection function.

Signal

Description

Time base

3PH active power (P)

Total three-phase active power

5ms

3PH reactive power (Q)

Total three-phase reactive power

5ms

3PH apparent power

Total three-phase apparent power

5ms

Pick-up

The PQS>/< setting parameter controls the pick-up of the power protection function. This defines the

maximum or minimum allowed measured three-phase power (active, reactive, or apparent) before

action from the function. The function constantly calculates the ratio between the PQS>/< and the

measured power magnitude. The reset ratios of 97 % (pick-up mode "Over") and 103 % (pick-up mode

"Under") are built into the function and is always relative to the pick-up value.

Q-G215

-G215

Instruction manual

Version: 2.04

197

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды