Arcteq AQ-G215 Скачать руководство пользователя страница 42

Страница: 42 / 458

4.7 Measurement menu

Figure. 4.7 - 40. Measurement section.

The

Measurement menu includes the following submenus: Transformers, Frequency, Current

measurement, Voltage measurement, Power and energy measurement, Impedance calculations, and

Phasors. The available measurement submenus depends on the type of IED in use. The ratio used by

the current and voltage transformers is defined in the

Transformers submenu, while the system nominal

frequency is specified in the

Frequency submenu. Other submenus are mainly for monitoring purposes.

Transformers

Figure. 4.7 - 41. Transformers section.

Transformers menu is used for setting up the measurement settings of available current transformer

modules or voltage transformer modules. Some unit types have more than one CT or VT module.

Some unit types like AQ-S214 do not have current or voltage transformers at all.

Q-G215

-G215

Instruction manual

Version: 2.04

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды