Arcteq AQ-G215 Скачать руководство пользователя страница 247

Страница: 247 / 458

Table. 5.3.19 - 166. Setting parameters for reset time characteristics.

Name

Range

Step

Default

Description

Release

time delay

0.000…150.000s 0.005s 0.06s

Resetting time. Time allowed between pick-ups if the pick-up has not led

to a trip operation. During this time the START signal is held on for the

timers if the delayed pick-up release is active.

Delayed

pick-up

release

1: No

2: Yes

Resetting characteristics selection either as time-delayed or as instant

after the pick-up element is released. If activated, the START signal is

reset after a set release time delay.

Time calc

reset after

release

time

1: No

2: Yes

Operating timer resetting characteristics selection. When active, the

operating time counter is reset after a set release time if the pick-up

element is not activated during this time. When disabled, the operating

time counter is reset directly after the pick-up element reset.

Continue

time

calculation

during

release

time

1: No

2: Yes

1: No

Time calculation characteristics selection. If activated, the operating time

counter continues until a set release time has passed even if the pick-up

element is reset.

The user can reset characteristics through the application. The default setting is a 60 ms delay; the

time calculation is held during the release time.

In the release delay option the operating time counter calculates the operating time during the release.

When using this option the function does not trip if the input signal is not re-activated while the release

time count is on-going.

Events and registers

The 100 % stator earth fault protection function (abbreviated "SEF" in event block names) generates

events and registers from the status changes in START, TRIP and BLOCKED. The user can select

which event messages are stored in the main event buffer: ON, OFF, or both.

The events triggered by the function are recorded with a time stamp and with process data values.

Table. 5.3.19 - 167. Event codes.

Event number

Event channel

Event block name

Event code

Description

7040

110

SEF1

Start ON

7041

110

SEF1

Start OFF

7042

110

SEF1

Trip ON

7043

110

SEF1

Trip OFF

7044

110

SEF1

Block ON

7045

110

SEF1

Block OFF

The function registers its operation into the last twelve (12) time-stamped registers. The register of the

function records the ON event process data for START, TRIP or BLOCKED. The table below

presents the structure of the function's register content.

Table. 5.3.19 - 168. Register content.

Date and time

Event code

Trigger

voltage

Fault

voltage

Pre-fault

voltage

Trip time

remaining

Used SG

dd.mm.yyyy

hh:mm:ss.mss

7040-7045 Descr. Start average

voltage

Trip -20ms

averages

Start -200ms

averages

0 ms...1800s

Setting group

1...8 active

Q-G215

-G215

Instruction manual

Version: 2.04

246

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды