Arcteq AQ-G215 Скачать руководство пользователя страница 200

Страница: 200 / 458

Function blocking

The block signal is checked in the beginning of each program cycle. The blocking signal is received

from the blocking matrix in the function's dedicated input. If the blocking signal is not activated when

the pick-up element activates, a START signal is generated and the function proceeds to the time

characteristics calculation.

If the blocking signal is active when the pick-up element activates, a BLOCKED signal is generated and

the function does not process the situation further. If the START function has been activated before the

blocking signal, it resets and the release time characteristics are processed similarly to when the pick-

up signal is reset.

The blocking of the function causes an HMI display event and a time-stamped blocking event with

information of the startup voltage values and its fault type to be issued.

The blocking signal can also be tested in the commissioning phase by a software switch signal when

the relay's testing mode "Enable stage forcing" is activated (

General

→

Device).

The variables the user can set are binary signals from the system. The blocking signal needs to reach

the device minimum of 5 ms before the set operating delay has passed in order for the blocking to

activate in time.

Operating time characteristics for trip and reset

This function supports definite time delay (DT). For detailed information on this delay type please refer

to the chapter "General properties of a protection function" and its section "Operating time

characteristics for trip and reset".

Events and registers

The power protection function (abbreviated "PQS" in event block names) generates events and

registers from the status changes in START, TRIP and BLOCKED. The user can select which event

messages are stored in the main event buffer: ON, OFF, or both. The function offers four (4)

independent stages; the events are segregated for each stage operation.

The events triggered by the function are recorded with a time stamp and with process data values.

Table. 5.3.15 - 137. Event codes.

Event number

Event channel

Event block name

Event code

Description

6400

100

PQS1

Start ON

6401

100

PQS1

Start OFF

6402

100

PQS1

Trip ON

6403

100

PQS1

Trip OFF

6404

100

PQS1

Block ON

6405

100

PQS1

Block OFF

6406

100

PQS2

Start ON

6407

100

PQS2

Start OFF

6408

100

PQS2

Trip ON

6409

100

PQS2

Trip OFF

6410

100

PQS2

Block ON

6411

100

PQS2

Block OFF

Q-G215

-G215

Instruction manual

Version: 2.04

199

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды