Arcteq AQ-G215 Скачать руководство пользователя страница 192

Страница: 192 / 458

Figure. 5.3.14 - 135. Operation of the df/dt>/< function when the frequency starts but doesn’t trip.

The figure above presents an example of the df/dt>/< function's operation when the frequency is

decreasing. If the f<

limit

and/or f>

limit

is activated, the function does not trip no matter how fast the

measured frequency changes if it’s over the f<

limit

or under f>

limit

. As can be seen in the figure above,

when the frequency decreases under the f<

limit

,tripping is allowed although the change of frequency is

not yet fast enough for the function to trip. Later the frequency makes a fast dip and as a result the

change of frequency is faster than the set pick-up value which then causes the relay to operate.

Each stage can be activated and deactivated individually. After the f>/< mode has been activated

(

Protection

→

Stage activation

→

Frequency stages), the user can activate and deactivate the

individual stages at will (

Protection

→

Frequency

→

Frequency protection f >/<

→

INFO

→

Stage

operational setup).

The outputs of the function are the START, TRIP and BLOCKED signals. The frequency protection

function uses a total of eight (8) separate setting groups which can be selected from one common

source.

The function can operate on instant or time-delayed mode.

The operational logic consists of the following:

• input magnitude processing
• threshold comparator
• two block signal check
• time delay characteristics
• output processing.

The inputs for the function are the following:

• operating mode selections
• setting parameters
• digital inputs and logic signals

Q-G215

-G215

Instruction manual

Version: 2.04

191

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды