Arcteq AQ-G215 Скачать руководство пользователя страница 242

Страница: 242 / 458

If the blocking signal is active when the pick-up element activates, a BLOCKED signal is generated and

the function does not process the situation further. If the START function has been activated before the

blocking signal, it resets and processes the release time characteristics similarly to when the pick-up

signal is reset.

The blocking of the function causes an HMI display event and a time-stamped blocking event with

information of the startup power values and its fault type to be issued.

The blocking signal can also be tested in the commissioning phase by a software switch signal when

the relay's testing mode "Enable stage forcing" is activated (

General

→

Device).

The variables the user can set are binary signals from the system. The blocking signal needs to reach

the device minimum of 5 ms before the set operating delay has passed in order for the blocking to

activate in time.

Operating time characteristics for trip and reset

This function supports definite time delay (DT). For detailed information on this delay type please refer

to the chapter "General properties of a protection function" and its section "Operating time

characteristics for trip and reset".

Events and registers

The underexcitation function (abbreviated "UEX" in event block names) generates events and registers

from the status changes in START, TRIP and BLOCKED. The user can select which event messages

are stored in the main event buffer: ON, OFF, or both.

The events triggered by the function are recorded with a time stamp and with process data values.

Table. 5.3.18 - 160. Event codes.

Event number

Event channel

Event block name

Event code

Description

6976

109

UEX1

Start ON

6977

109

UEX1

Start OFF

6978

109

UEX1

Trip ON

6979

109

UEX1

Trip OFF

6980

109

UEX1

Block ON

6981

109

UEX1

Block OFF

The function registers its operation into the last twelve (12) time-stamped registers. The register of the

function records the ON event process data for START, TRIP or BLOCKED. The table below

presents the structure of the function's register content.

Table. 5.3.18 - 161. Register content.

Date and time

Event code

Trigger

power (P&Q)

Fault power

(P&Q)

Pre-fault

power (P&Q)

Trip time

remaining

Used SG

dd.mm.yyyy

hh:mm:ss.mss

6976-6981 Descr. Start average

power

Trip -20ms

averages

Start -200ms

averages

0 ms...1800s

Setting group

1...8 active

Q-G215

-G215

Instruction manual

Version: 2.04

241

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды