Arcteq AQ-G215 Скачать руководство пользователя страница 241

Страница: 241 / 458

Pick-up

The

set

< setting parameter controls the pick-up of the Q< function. This defines the minimum allowed

measured three-phase reactive power before action from the function. The function constantly

calculates the ratio between the

set

< and the measured magnitude (Q

). The reset ratio of 97 % is

built into the function and is always relative to the

set

< value.

Table. 5.3.18 - 158. Pick-up settings.

Name

Range

Step

Default

Description

Qset mode

0: Fixed

1: P-

dependent

0: Fixed

Decides whether the pick-up area is defines only by the

set

< parameter

or by two points set in the PQ plane.

Qset<

0.0…-100

000kvar

0.01kvar -100kvar

In Fixed mode: sets the pick-up value for the function.

In P-dependent mode: chooses the reactive power for the first point.

Pick-up P1

for Qset<

0.0…-100

000kW

0.01kW

100kW

The value of the active power for

set

< when the P-dependent mode is

in use.

Qset2<

0.0…-100

000kvar

0.01kvar -100kvar Chooses the reactive power for the second point when the P-dependent

mode is in use.

Pick-up P2

for Qset<

0.0…-100

000kW

0.01kW

100kW

The value of the active power for

set2

< when the P-dependent mode is

in use.

The pick-up activation of the function is not directly equal to the START signal generation of the

function. The START signal is allowed if the blocking condition is not active.

Read-only parameters

The relay's

Info page displays useful, real-time information on the state of the protection function. It is

accessed either through the relay's HMI display, or through the setting tool software when it is

connected to the relay and its Live Edit mode is active.

Table. 5.3.18 - 159. Information displayed by the function.

Name

Range

Step

Description

condition

0: Normal

1: Start

2: Trip

3: Blocked

Displays the status of the protection function.

Expected

operating

time

0.000...1800.000s

0.005s

Displays the expected operating time when a fault occurs.

Time

remaining

to trip

-1800.000...1800.000s

0.005s

When the function has detected a fault and counts down time

towards a trip, this displays how much time is left before tripping

occurs.

meas

set

at the

moment

-1250.00...1250.00Q

set

0.01Q

set

The ratio between the measured reactive power and the pick-up

value.

Function blocking

The block signal is checked in the beginning of each program cycle. The blocking signal is received

from the blocking matrix in the function's dedicated input. If the blocking signal is not activated when

the pick-up element activates, a START signal is generated and the function proceeds to the time

characteristics calculation.

Q-G215

-G215

Instruction manual

Version: 2.04

240

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды