Arcteq AQ-G215 Скачать руководство пользователя страница 298

Страница: 298 / 458

Figure. 5.4.1 - 189. Setting group control – two-wire connection from Petersen coil status with additional logic.

The images above depict a two-wire connection from the Petersen coil: the two images at the top

show a direct connection, while the two images on the bottom include additional logic. With a two-wire

connection the state of the Petersen coil can be monitored more securely. The additional logic ensures

that a single wire loss will not affect the correct setting group selection.

The application-controlled setting group change can also be applied entirely from the relay's internal

logics. For example, the setting group change can be based on the cold load pick-up function (see the

image below).

Q-G215

-G215

Instruction manual

Version: 2.04

297

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды