Arcteq AQ-G215 Скачать руководство пользователя страница 125

Страница: 125 / 458

Broad range mode with multi-criteria detection for unearthed and compensated

networks

When detecting earth faults in compensated long-distance cables and overhead lines, it is in some

cases difficult to distinguish between a healthy and a faulty feeder. Merely measuring the angle and

the magnitude of residual voltage and currents is not always enough, as changes in symmetrical

components of phase currents and voltages are also needed. Additionally, when protecting feeders

from earth faults, two modes are used depending on the network status (unearthed or compensated).

When changing between these two statuses the setting group must be changed, and especially

with distributed compensation the change may be difficult or impossible to arrange. Finally, in a

compensated network protection the relay with traditional algorithms may sporadically detect an earth

fault in a long healthy feeder due to CT errors. For all these reasons, Arcteq has developed an

improved alternative to these traditional directional earth fault protections.

Figure. 5.3.5 - 96. Angle tracking of the I0dir> function (broad range mode).

Q-G215

-G215

Instruction manual

Version: 2.04

124

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды