Arcteq AQ-G215 Скачать руководство пользователя страница 62

Страница: 62 / 458

Problem

Solution

The measured current

amplitudes are OK but

the angles are strange./

The phase unbalance

protection trips

immediately after

activation./

The earth fault

protection trips

immediately after

activation.

The phase currents are connected to the measurement module but the order or polarity of one or all

phases is incorrect. In relay settings, go to

Measurement

→

Phasors and check the "Phase current

vectors" diagram. When all connections are correct, the diagram (symmetric feeding) should look

like this:

See the following tables for the most common problems with phase polarity and network rotation

(mixed phases).

The following image presents the most common problems with phase polarity. Problems with phase

polarity are easy to find because the vector diagram points towards the opposite polarity when a phase

has been incorrectly connected.

Q-G215

-G215

Instruction manual

Version: 2.04

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды