Arcteq AQ-G215 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 458

background image

Connections

Figure. 4.6 - 38. View of the Connections submenu.

The

Connections submenu offers the following bits of information and settings:

ETHERNET

ETHERNET

This section defines the IP settings for the ethernet port in the back panel of the unit.

• IP address: the IP address of the device which can be set by the user (the default IP address

depends on the device).

• Network: the network subnet mask is entered here.
• Gateway: the gateway is configured only when communicating with the devices in a separate

subnet.

• MAC-Address: Unique MAC address of the device. Not configurable by user.

SERIAL COM

SERIAL COM

This section defines the basic settings of RS-485 port in the back panel of the unit.

• Bitrate: displays the bitrate of the RS-485 serial communication interface (9600 bps as

standard, although can be changed to 19 200 bps or 38 400 bps if an external device

supports the faster speed).

• Databits, Parity and Stopbits: these can be set according the connected external devices.
• Protocol: by default the device does not have any serial protocol activated, although IEC

103, Modbus I/O and Modbus/RTU can be used for communication.

NO

NOTE!

TE!

When communicating with a device through a front Ethernet port connection, the IP address

is always 192.168.66.9.

SERIAL COM1 & COM2

SERIAL COM1 & COM2

SERIAL COM1 and SERIAL COM2 are reserved for serial communication option cards. They have the

same settings as RS-485 port.

A

AQ

Q-G215

-G215

Instruction manual

Version: 2.04

39

«
...
38
39
40
41
42
...
»

Содержание AQ-G215











































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AQ-G215

Бренд: ISC Страницы: 12

Бренд: Haas Страницы: 7

Бренд: Russound Страницы: 4

Бренд: OBO Bettermann Страницы: 68

Бренд: ICON Страницы: 84

Бренд: Samsung Страницы: 69

Бренд: Panasonic Страницы: 18

Бренд: Omni cubed Страницы: 9

Бренд: Priorit Страницы: 9

PRIODOOR ETX-RDA

Бренд: Priorit Страницы: 21

Бренд: Entes Страницы: 2

Бренд: Kitronik Страницы: 2

Бренд: Bticino Страницы: 8

Бренд: Deltaplus Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды