APS CFS108 Скачать руководство пользователя

Страница: 95 / 146

CFS100 SERIES OPERATION MANUAL

SECTION 6: FRONT PANEL OPERATION

Entire Contents Copyright



APS CFS100 Series Power Source Operation Manual

Page 95 of 146

6.15

MANUAL (AC) Mode Execution

In MANUAL mode of operation, the setup screen will look as shown here. The Manual mode

is indicated by the lack of a Step number after the M number in upper left corner of the LCD.

To enable the output and apply power to a unit under test, press the Test/Reset key and the

LED for the key will illuminate. The text “

Set

” on the set screen will turn to “

Dwell

”, in

addition, the soft keys will change to include “Meter”, “AUTO”, “Keypad” and “Trig.”.
In MANUAL Mode, the output will run continuously (infinite dwell time) until the Test/Reset

key is pressed again, or there is a failure condition. The Test/Reset LED will be on during this

time.

The following Soft keys are active during MANUAL mode output on state:

Meter

The “

Meter

” soft key allows the right hand side large font readout to be

toggle between all available measurements

AUTO / HIGH

The “

AUTO

” and “

HIGH

” soft keys appear in the same location and toggle

the voltage range between High and Low.

Note

that if the programmed

voltage is 150V or higher, the power source will remain in high voltage

range. If the programmed voltage is less than 150V, selecting AUTO will

result in the low voltage range being used allowing two times the amount of

current to be delivered to the unit under test.

Keypad

The “

Keypad

” soft key may be used to enter a different voltage or

frequency value directly using the Key pad. This means output voltage

and/or frequency can be changed without having to open the output (OFF).

You can also use the shuttle knob for this. Unless the Frequency is displayed

in large font on the right, the “

Keypad

” soft key and Shuttle both will adjust

the output voltage. If Frequency is displayed on the right, “Keypad” soft key

and shuttle will adjust the frequency.

Содержание CFS108



















































































































































Результаты поиска

Содержание CFS108

Отзывы:

Похожие инструкции для CFS108

Бренды по названию

Популярные бренды

APS CFS108, Руководство по эксплуатации

Результаты поиска

Содержание CFS108

Отзывы:

Похожие инструкции для CFS108

Бренды по названию

Популярные бренды