APS CFS108 Скачать руководство пользователя страница 84

Страница: 84 / 146

CFS100 SERIES OPERATION MANUAL

SECTION 6: FRONT PANEL OPERATION

Entire Contents Copyright



APS CFS100 Series Power Source Operation Manual

Page 84 of 146

6.12.7

Surge/Drop Programming

To program the Surge/Drop parameters, use the “

∧

∨

” soft keys to navigate to the

Surge/Drop parameter. Pressing the “

Edit

” soft key will display the screen shown below.

The Surge/Drop field is either set to ON or OFF using the “

Change

” soft key. The two modes

are defined as follows:

OFF:

Surge/Drop feature is disabled so no voltage surge or sag will take place. When OFF,

additional SD-Volt screens will not be visible.

ON:

Surge/Drop feature is enabled. This means the SD-Volt parameters all have to be

programmed to determine the level and duration of the voltage surge or sag.

To change the Surge/Drop mode between

OFF

, press the “

Change

” soft key to toggle

between the two selections. Press the “

Enter

” soft key to accept the parameter, or press the

“

Esc

” soft key to move back to the voltage parameter screen. You must press the Enter soft

key for the new setting to take effect transitions the screen to the next parameter: SD-Volt.

Note:

The user can bypass editing this parameter and move to the next or previous

parameter set screen by pressing the “

Prev

” or “

Next

” soft key.

When Surge/Drop is ON, the following additional parameter screens will be accessible in the

order shown here:

SD-Volt

Surge or Drop Voltage level. Surge versus Drop is determined by the values

of Voltage and SD-Volt. If Voltage > SD-Volt, a Drop will occur. If Voltage <

SD-Volt, a Surge will occur.

SD-Site

Time offset from 0° Phase angle of output voltage where the surge or drop

will start. Note that the Start and Stop phase angles for the program

memory (See Section 6.12.1, “Phase Angles”) do NOT apply here. The 0° is

with respect to the sinewave.

SD-Time

Duration of the voltage surge or drop in msecs. Note that the range for this

parameter is 0-20 msec when SD-Cont is ON or 0-99 msec when SD-Cont is

OFF.

Содержание CFS108



















































































































































Результаты поиска

Содержание CFS108

Отзывы:

Бренды по названию

Популярные бренды

APS CFS108, Руководство по эксплуатации

Результаты поиска

Содержание CFS108

Отзывы:

Бренды по названию

Популярные бренды