APS CFS108 Скачать руководство пользователя страница 41

Страница: 41 / 146

CFS100 SERIES OPERATION MANUAL

SECTION 5: UNPACKING & INSTALLATION

Entire Contents Copyright



APS CFS100 Series Power Source Operation Manual

Page 41 of 146

5.4

AC Input Connections

All CFS100 units operate on single phase AC input and are furnished with either an IEC line

cord or a terminal block for AC input (CFS140). For the CFS140, a suitable line cord and

power disconnect is required (but not included) to connect to the mains.
Refer to Section 5.6, “Check Line Voltage" to see how to check the line voltage selection and

fuse type.
The AC input connections must be made at the rear of the CFS100 units. For the CFS140, a

single safety cover is provided to cover both AC input and AC/DC Output terminal blocks.

CAUTION

The included output safety covers must be properly

installed when using this equipment

•

The AC input terminal on the CFS140 is marked. A three wire mains connection is

required. (L1, L2 and Earth Ground).

•

Model CFS108 is furnished with an IEC 60320 C13 15A line cord.

•

Model CFS116 is furnished with an IEC 60320 C19 20A line cord.

5.5

Grounding Requirements

WARNING

SHOCK HAZARD

EQUIPMENT MUST BE GROUNDED

The chassis must be grounded. A proper Earth Ground connection must be used at all times.

Correct grounding of your electrical system infrastructure according to applicable national

standards must be observed.

Содержание CFS108



















































































































































Результаты поиска

Содержание CFS108

Отзывы:

Бренды по названию

Популярные бренды

APS CFS108, Руководство по эксплуатации

Результаты поиска

Содержание CFS108

Отзывы:

Бренды по названию

Популярные бренды