APRILIA RSV4 R Скачать руководство пользователя

Страница: 70 / 475

Specific tooling

020850Y

Primary gear lock

020848Y

Flywheel retainer

Repeat the following operations:

•

move cylinder piston 1 (left rear piston)

to TDC;

•

turn the crankshaft 150° in the direction

of engine rotation (direction of travel) in

order to align the hole on the intake

camshaft with the specific hole on the

U bolt; this ensures that all the front

cylinder bank valve springs are decom-

pressed.

•

Refit the camshaft timing setting pin in

the hole in the U bolt on the front head,

and refit the crankshaft timing pin from

the flywheel side, to check that the tim-

ing setting was not altered while the

engine was turned with only one cam-

shaft drive gear fastener screw in

place.

•

Remove the camshaft timing pin.

•

Unscrew and remove the two U bolt

screws (1).

•

Remove the U bolt and the oil pipe.

Specific tooling

020851Y

Camshaft timing pin

020852Y

Crankshaft timing pin

•

Block crankshaft rotation using one of

the specific tools.

•

Unscrew and remove the second in-

take camshaft gear screw.

•

Leave the gear on the camshaft.

Specific tooling

020848Y

Flywheel retainer

020850Y

Primary gear lock

Maintenance

RSV4 R

MAIN - 70

Содержание RSV4 R




























































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды

APRILIA RSV4 R, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды