APRILIA RSV4 R Скачать руководство пользователя страница 250

Страница: 250 / 475

Checking the forks

The purpose of the springs at the end of the gearbox control rods is to reduce vibration and make it

easier to engage the gears.

Characteristic

Maximum selection fork axial clearance

0.5 mm (0.020 in)

Minimum wear limit of the selection fork guide pins

6.8 mm (0.27 in)

Maximum eccentricity of the two fork guide shafts

0.05 mm (0.0020 in)

NOTE

THE FOLLOWING PROCEDURE IS VALID FOR ALL GEARBOX FORKS.

•

Check the transmission fork cam roller

«1» and the transmission fork tooth

«2» for damage, deformation and

wear.

•

Replace the transmission fork if nec-

essary.

•

Check the transmission fork movement and if it is not regular, replace the transmission forks.

Assembling the gearbox

•

Move the gearbox primary and secon-

dary shafts together and fit them into

the cover.

NOTE

SECURE THE SHIM WASHER TO THE SECONDARY
SHAFT WITH GREASE.

NOTE

MAKE SURE THE SLIDING BUSHING IS PRESENT ON EVERY GEAR CONTROL FORK.

Engine

RSV4 R

ENG - 250

Содержание RSV4 R




























































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды

APRILIA RSV4 R, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды