APRILIA RSV4 R Скачать руководство пользователя

Страница: 295 / 475

020851Y

Camshaft timing pin

020852Y

Crankshaft timing pin

•

Block crankshaft rotation using one of

the specific tools.

•

Unscrew and remove the second in-

take camshaft gear screw.

•

Leave the gear on the camshaft.

Specific tooling

020848Y

Flywheel retainer

020850Y

Primary gear lock

•

Install the specific camshaft gear sup-

port tool.

•

Fix it to the head using the two screws

(1).

•

Move the gear from the camshaft to the

tool.

Specific tooling

020865Y

Support for camshaft gear on head

•

Unscrew and remove the eight screws

(2), proceeding in stages and diago-

nally.

•

Retrieve the washers from the screws

near the spark plug holes.

•

Remove the U bolts with the O rings

and locator pins.

•

Remove the intake and exhaust cam-

shafts.

If the two camshafts are timed correctly, the intake

camshaft gear tooth (indicated with one dot) is

meshed with the trough of the exhaust camshaft

gear (indicated with two dots).

RSV4 R

Engine

ENG - 295

Содержание RSV4 R




























































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды

APRILIA RSV4 R, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды