APRILIA RSV4 R Скачать руководство пользователя страница 139

Страница: 139 / 475

In this mode, a chart is displayed showing potential errors in the immobilizer and the sensors connected

to it.

DSB 01

- Immobilizer fault: key code read but not recognised.

DSB 02

- Immobilizer fault: key code not read (key not present or transponder not working)

DSB 03

- Immobilizer fault: aerial not working (open or short-circuited)

DSB 04

- Internal controller fault

DSB 05

- -

DSB 06

- -

Error cause

•

An oil sensor fault is signalled when it is detected that the sensor circuit is open or shorted

to positive.

DSB 07

- Oil pressure sensor

Error cause

An oil sensor fault is signalled when, with engine off, it is detected that the sensor circuit is open.

Troubleshooting

The test is performed only once when the key is set to ON. This error is signalled by the bulb icon, and

the general warning light turns on as well.

DSB 08

- Oil pressure sensor

Error cause

An oil sensor fault is signalled when, with engine running, it is detected that the sensor circuit is closed.

There is an error when the general warning light turns on.

Troubleshooting

This error is signalled by the bulb icon, and the general warning light turns on as well.

The instrument panel must keep all previous errors stored in its memory.

DELETE ERRORS

This option deletes all instrument panel errors; a further confirmation is requested. Use Axone to reset

ECU errors.

VEHICLE SERVICING RESET

This function is used to reset vehicle servicing. Using this function, the odometer can be reset only once

within the first 200 km (124 mi) of the vehicle, provided this has not been done by the Quality Check.

UPDATE

This function is used to program the instrument panel again. This screen page shows the software

version currently loaded; the LCD reads:

•

INSTRUMENT PANEL DISCONNECTED. NOW CONNECT THE DIAGNOSIS INSTRU-

MENT.

The instrument panel will restart to work normally after the key is inserted-extracted.

RSV4 R

Electrical system

ELE SYS - 139

Содержание RSV4 R




























































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды

APRILIA RSV4 R, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды