APRILIA RSV4 R Скачать руководство пользователя страница 424

Страница: 424 / 475

Removal

•

Remove the front wheel.

The following operations refers to a single disc

but apply to both.

To unscrew the screws (1), use an air screwer gun

to give a clean blow, which will detach the screws

stuck with LOCTITE 243.

•

Unscrew and remove the six brake disc

screws (1).

•

Remove the brake disc (2).

UPON REFITTING, APPLY LOCTITE 243 ON THE THREAD
OF THE BRAKE DISC SCREWS (1).

CAUTION

UPON REFITTING, SCREW ALL THE SCREWS (1) MAN-
UALLY AND TIGHTEN THEM OPERATING DIAGONALLY
FOLLOWING THIS SEQUENCE: A-B-C-D-E-F.

See also

Removing the front wheel

Disc Inspection

•

The following operations must be car-

ried out with the brake discs fitted on

the wheel; they refer to a single disc,

but are valid for both.

•

Check the disc for wear by measuring

the minimum thickness with a micro-

meter in different points. If the mini-

mum thickness, even in a single point

of the disc, is less than the minimum

value, replace the disc.

Disc thickness minimum value: 4 mm (0.16 in)

•

Using a dial gauge, check that the max-

imum oscillation of the disc does not

exceed the tolerance; otherwise, re-

place it.

Braking system

RSV4 R

BRAK SYS - 424

Содержание RSV4 R




























































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды

APRILIA RSV4 R, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды