APRILIA RSV4 R Скачать руководство пользователя | Manualshive

Страница: 366 / 475

background image

F

RONT

FORK

pos.

Description

Type

Quantity

Torque

Notes

1

Calliper mounting bracket fixing

screws

M8

2+2

22 Nm (16.23 lbf ft)

-

2

Pumping member fixing screw

-

1+1

30 - 39 Nm (22.13 -

28.76 lbf ft)

-

3

Sleeve top cap

-

1+1

30 - 39 Nm (22.13 -

28.76 lbf ft)

-

Adjustment

Standard front fork setting is adjusted to suit most

high and low speed riding conditions, whether the

vehicle is partially or fully loaded.

However, the setting can be modified for specific

needs according to vehicle use.

RACING TRACK SETTINGS MUST BE DONE ONLY FOR
OFFICIAL COMPETITIONS OR SPORTS EVENTS WHICH
ARE, IN ALL CASES, AWAY FROM NORMAL ROAD TRAF-
FIC AND WITH THE AUTHORISATION OF THE RELEVANT
AUTHORITIES.
IT IS STRICTLY FORBIDDEN TO RIDE A VEHICLE SET FOR
RACING ON ROADS AND MOTORWAYS.

WHEN COUNTING THE NUMBER OF CLICKS AND/OR
TURNS OF ADJUSTMENT SCREWS (1 - 2), ALWAYS
START FROM THE STIFFEST SETTING (ADJUSTER
SCREW TURNED FULLY CLOCKWISE). WHEN COUNTING
THE NUMBER OF CLICKS AND/OR TURNS OF ADJUST-
MENT SCREW (3), ALWAYS START FROM THE SOFTEST
SETTING (ADJUSTER SCREW TURNED FULLY ANTI-
CLOCKWISE).

FRONT FORK - STANDARD

SETTING

(

FOR

ROAD

USE

ONLY

)

Specification

Desc./Quantity

Rebound damping adjustment, screw (1)

Unscrew (**) 1.5 turns from fully closed (*)

Compression damping adjustment, screw (2)

Unscrew (**) 1 turn from fully closed (*)

Spring preloading, nut (3)

Unscrew (**) 5 notches from fully closed (*)

Stems (A) (***) protrusion from top plate (excluding cover)

3 notches/ 12 mm (3 notches/0.47 in)

Theoretical fork failure (moto rider 70kg - 154lb) (B)

33-35 +/- 1 mm (1.30-1.38 +/- 0.039 in)

FRONT FORK - RACING

ADJUSTMENT

RANGE

(

TRACK

USE

ONLY

)

Specification

Desc./Quantity

Rebound damping adjustment, screw (1)

Unscrew (**) 3/4 - 1 turn (*) from fully closed

Compression damping adjustment, screw (2)

Unscrew (**) 0.5 turn from fully closed (*)

Spring preloading, nut (3)

Unscrew (**) 4 - 5 notches from fully closed (*)

Stems (A) (***) protrusion from top plate (excluding cover)

3 notches/ 12 mm (3 notches/0.47 in)

Theoretical fork failure (moto rider 70kg - 154lb) (B)

35 +/- 1 mm (1.38 +/- 0.039 in)

Suspensions

RSV4 R

SUSP - 366

«
...
364
365
366
367
368
...
»

Содержание RSV4 R




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RSV4 R

Бренд: Yoshimura Страницы: 7

Бренд: LAMAX Страницы: 134

950 SUPER ENDURO R 2006

Бренд: KTM Страницы: 86

Бренд: Caberg Страницы: 16

Бренд: KTM Страницы: 90

Multistrada 620

Бренд: Ducati Страницы: 382

Бренд: MOTO GUZZI Страницы: 134

Бренд: Aim Страницы: 47

Бренд: Montesa Страницы: 114

4Ride MST260 2016

Бренд: Montesa Страницы: 158

2005 F4 BRUTALE 910 S

Бренд: MV Agusta Страницы: 195

Бренд: MV Agusta Страницы: 467

Бренд: HJC Страницы: 7

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

TOPMASTER V0NR55ST

Бренд: Shad Страницы: 2

TOPMASTER Y0TM52ST

Бренд: Shad Страницы: 3

Бренд: Shad Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды