APRILIA RSV4 R Скачать руководство пользователя | Manualshive

Страница: 86 / 475

background image

The engine does not start

THE ENGINE DOES NOT START, THE INSTRUMENT PANEL TURNS ON.

CAUTION

AXONE SHOULD BE WORKING PROPERLY AND UPGRADED AT LEAST TO THE 7.0.0 VERSION
OR THE PGDS UPDATED AT LEAST TO THE 3.0.0 VERSION

CAUTION

BEFORE ANY TROUBLESHOOTING, MAKE SURE THAT:
1) BATTERY VOLTAGE IS ABOVE 12V;
2) THE MAIN 30A FUSE IS NOT DAMAGED AND IS ADEQUATELY FITTED;
3) AUXILIARY FUSES ARE NOT DAMAGED AND ARE ADEQUATELY FITTED.

NOTE

THE RELAY NUMBER SPECIFIED REFERS TO THE WIRING DIAGRAM. THE POSITION OF THE
RELAY ON THE VEHICLE IS INDICATED IN THE "ELECTRICAL SYSTEM/COMPONENT LAYOUT/
RELAY LAYOUT" CHAPTER.

•

1- WITH THE KEY TURNED TO "ON", THE INSTRUMENT PANEL LIGHTS UP BUT NO

FAULT INDICATION IS SHOWN WITH INDICATION "SERVICE" OR "URGENT SERVICE"

BUT THE WORD ECU IS READ BELOW and THE PLUG SOCKET DISCONNECTED?

YES, go to CONTROL UNIT SUPPLY CHECK;

NO, go to 2

•

2. IS THE FUEL PUMP ACTIVATED?

YES, go to 3; NO, go to FUEL PUMP CHECK

•

3. THE DIAGNOSIS INSTRUMENT COMMUNICATES WITH THE CONTROL UNIT? THAT

IS, AFTER SELECTING FUEL INJECTION, AND FOLLOWING THE INSTRUCTION, WITH

KEY SET TO "ON", THE PARAMETERS, STATUSES, ETC ARE READ?

YES, go to 4; NO, go to DIAGNOSIS INSTRUMENT CONNECTION CHECK

•

4. WITH DIAGNOSIS INSTRUMENT ("DEVICES ACTIVATION" SCREEN PAGE, INJEC-

TOR ICON) CARRY OUT ACTIVATION OF A LOWER INJECTOR (IT IS ADVISED TO

DISCONNECT THE BLACK FUEL PUMP CONNECTOR AT PIN 4, ON THE RIGHT): IS

THE INJECTOR ACTIVATED?

YES, go to 5, NO, go to INJECTION RELAY 33 CHECK

5. DOES THE MOTOR TURN WHEN THE STARTER SWITCH IS PRESSED?

YES, SEE CHAPTER "ELECTRICAL SYSTEM/CHECK AND CONTROLS/ENGINE SPEED SEN-

SOR and if engine speed sensor works correctly, go to 16; NO, go to 6

•

6. WHAT DOES THE "START-UP ENABLING SWITCH" STATUS IN THE DIAGNOSIS

INSTRUMENT, DEVICES STATUS SCREEN PAGE, ICON 0/1 MEAN?

YES, go to STARTER SWITCH CHECK; NO, go to 7

•

7. WHAT DOES THE "FALL SENSOR" STATUS IN THE DIAGNOSIS INSTRUMENT, DE-

VICES STATUS SCREEN PAGE, ICON 0/1 MEAN?

If NORMAL is shown, go to 8; if TIP OVER is shown, go to 12

Troubleshooting

RSV4 R

TROUBL - 86

«
...
84
85
86
87
88
...
»

Содержание RSV4 R




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RSV4 R

Saddle Tramp BC-BTHBSP

Бренд: Metra Electronics Страницы: 8

Бренд: CF MOTO Страницы: 443

990D0-28K50-CLE

Бренд: Suzuki Страницы: 12

Бренд: N-Com Страницы: 2

690 Enduro AUS 2010

Бренд: KTM Страницы: 265

Бренд: Megelli Страницы: 83

RMAX WOLVERINE 2021

Бренд: Yamaha Страницы: 192

Бренд: Yamaha Страницы: 396

Бренд: Yamaha Страницы: 192

Бренд: Shark Страницы: 92

Бренд: hepco & becker Страницы: 6

Бренд: Thunderbike Страницы: 8

Бренд: MOTO GUZZI Страницы: 48

Бренд: MOTO GUZZI Страницы: 198

2002 California Special Sport

Бренд: MOTO GUZZI Страницы: 155

Бренд: MOTO GUZZI Страницы: 357

Бренд: BMS Страницы: 11

Бренд: Malaguti Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды