APRILIA RSV4 R Скачать руководство пользователя страница 74

Страница: 74 / 475

•

Remove the two crankshaft and cam-

shaft reference pins.

•

Turn the crankshaft until the gear

screw covered by the head when the

hole on the camshaft gear is aligned

with the hole on the U bolt, is visible.

•

Block crankshaft rotation using one of

the specific tools.

•

Apply Loctite 243 thread lock on the

thread of the second gear fastener

screw. This screw must be replaced at

each reassembly.

•

Tighten the second camshaft gear fix-

ing screw to exactly the torque speci-

fied.

•

Remove the crankshaft locking tool.

Specific tooling

020848Y

Flywheel retainer

020850Y

Primary gear lock

020851Y

Camshaft timing pin

020852Y

Crankshaft timing pin

•

Turn the crankshaft back to the previous position in which the camshaft and U bolt holes

were aligned; insert the reference pin while checking with the crankshaft reference pin, that

the flywheel side hole and the hole on the crankshaft are perfectly aligned.

•

If this is not the case, repeat the timing operations.

Specific tooling

020851Y

Camshaft timing pin

020852Y

Crankshaft timing pin

•

Check if the clearance between the cam on the shaft and the tappet is correct.

•

If not, repeat the valve clearance adjustment procedure.

Rear cylinder head valves

•

Check the rear valve head clearance and restore the correct clearance values if necessary,

proceeding as described below.

•

Remove the rear head cover and the clutch cover.

•

Move cylinder piston 1 (left rear piston) to the TDC;

Maintenance

RSV4 R

MAIN - 74

Содержание RSV4 R




























































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды

APRILIA RSV4 R, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды