APRILIA RSV4 R Скачать руководство пользователя

Страница: 151 / 475

Variable geometry intake

(IF AVAILABLE)

Function

Extend or shorten the engine inlet ducts to in-

crease the inlet air quantity according to the engine

revs.

Operation / operating principle

The system consists of:

•

two inlet ducts for each manifold, which

may be joined (long ducts) or separa-

ted (short ducts);

•

a motor that, by means of an endless

screw, activates the upper part of the

inlet ducts;

•

a variable geometry control unit for

managing the system, interfaced with

the engine injection control unit.

At key-ON, the variable geometry control unit low-

ers the ducts (if still in the raised position). Subse-

quently, depending on the control voltage on PIN

2 from the injection control unit (0V down, 5V up),

the control unit drives the electric motor with the

relative polarity for raising or lowering the ducts.

The drive voltage delivered to the motor is deter-

mined in relation to battery voltage and the motor

is stopped once a given current limit is reached or

if the time-out period of 500 ms has elapsed.

Level in wiring diagram:

Variable geometry

Location:

•

on the vehicle: ducts and motor inside

the filter box, variable geometry control

unit on rear frame under the saddle,

right side.

•

variable geometry control unit connec-

tor: on the control unit.

RSV4 R

Electrical system

ELE SYS - 151

Содержание RSV4 R




























































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды

APRILIA RSV4 R, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды