APRILIA RSV4 R Скачать руководство пользователя страница 75

Страница: 75 / 475

•

Turn the crankshaft 450° (one complete turn + 90°) in the direction of motor rotation (direction

of travel).

•

Insert the pin from the clutch side into

the hole in the crankshaft.

NOTE

THE SPECIAL TOOL IS ONLY USED FOR IDENTIFYING
THE CORRECT CRANKSHAFT POSITION.
DO NOT USE IT FOR TIGHTENING OPERATIONS.

Specific tooling

020852Y

Crankshaft timing pin

See also

Head cover removal
Removing the

clutch cover

•

Fit the pin aligning the intake camshaft

with the hole in the U bolt.

•

If it was not possible before adjusting

the valve clearance, check the engine

timing.

Specific tooling

020851Y

Camshaft timing pin

•

Remove the two crankshaft and cam-

shaft reference pins.

•

Turn the crankshaft until the gear

screw covered by the head when the

hole on the camshaft gear is aligned

with the hole on the U bolt, is visible.

•

Block crankshaft rotation using one of

the specific tools.

•

Unscrew and remove the camshaft

gear screw.

•

Remove the crankshaft locking tool.

Specific tooling

020850Y

Primary gear lock

020848Y

Flywheel retainer

RSV4 R

Maintenance

MAIN - 75

Содержание RSV4 R




























































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды

APRILIA RSV4 R, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды