APRILIA RSV4 R Скачать руководство пользователя страница 125

Страница: 125 / 475

TABLE ZS - NOTES FOR FITTING THE

GROUND CABLE

There are two ground lug terminals on the cable

harness: the "ENGINE GND" (output "9") and the

"CHASSIS GND" (output "10").

The lug terminal "ENGINE GND" (172) (output "9")

must be connected to the M6 hole on the upper

engine crankcase with a flanged M6x16 screw

(173). The other lug terminal "CHASSIS

GND" (174) (output "10") must be left free.

CAUTION

TAKE CARE NOT TO SWAP THE TWO GROUND LUG TER-
MINALS

TABLE ZQ - CONNECTORS FOR INTAKE DUCT CONTROL UNIT AND INTAKE DUCT MOTOR (If

available)

The "Intake duct mot." (output "32") connector (167) must be fastened with a small black clamp (170)

as shown in the figure.

167. Intake duct motor connector (output "32")

168. Cable harness routing

169. Intake duct motor cable harness connection (output "32")

170. Clamp

Back side

TABLE A - LICENSE PLATE FRAME PRE-FITTING

Check that the drainage hole (7) for the water of both turn indicators is positioned downward.

1. License plate frame cable harness

2. Cable harness routing

3. 2.8 mm (0.11 in) Faston - cable colours: red and blue

4. License plate light grey rubber ring

5. 2.8 mm (0.11 in) Faston - cable colours: light blue and blue

6. Left rear turn indicator cable harness routing

RSV4 R

Electrical system

ELE SYS - 125

Содержание RSV4 R




























































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды

APRILIA RSV4 R, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды