APRILIA RSV4 R Скачать руководство пользователя страница 137

Страница: 137 / 475

•

Immobilizer fault: aerial not working (open or short-circuited)

Error cause

•

An electric interruption or a ground short circuit or voltage to the circuit have been detected

Troubleshooting

•

Check the sensor connector on the cable harness and the instrument panel connector. If

not OK, restore; if OK, check electrical characteristics and aerial circuit continuity from the

instrument panel connector on PIN 24 and 34: if not OK, restore cable harness; if OK, check

circuit ground insulation: if not ground insulated, restore cable harness; if insulated, with key

ON, with instrument panel connector disconnected, check that there is not voltage at the

circuit ends: if there is voltage, restore the cable harness

DSB 04

Internal controller fault

Error cause

•

There is a fault in the instrument panel

Troubleshooting

•

Replace the instrument panel

Dashboard

In case of doubts in operation of the engine revs indication, it is possible to connect the vehicle to the

diagnosis instrument and activate the engine revs indication choosing the function "Rpm indicator" from

the "Devices Activation" screen page (injector icon)

Installing a new instrument panel

In case the instrument panel is replaced by a new one, follow the procedure shown below so that the

immobilizer system (key storage) and the exhaust butterfly valve (controlled by the ECU through the

instrument panel) operate correctly.

1. Request all the keys of the vehicle in the customer possession.

Once the instrument panel is electrically connected to the vehicle and a key is set to ON, the key is

stored and the instrument panel waits for 20 seconds for a possible second key. If there is a second

key, remove the first key and wait for the storage of the second key. When the second key storage is

complete, the instrument panel waits for another key up to a maximum of 4 total keys or the procedure

will be interrupted after 20 seconds.

At this stage, the instrument panel turns on as usual.

2. Deleting the errors stored by the instrument panel: select Menu and then Diagnosis. An access code

is required to enter this menu:

12412

Then, select the option: "Delete errors"

RSV4 R

Electrical system

ELE SYS - 137

Содержание RSV4 R




























































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды

APRILIA RSV4 R, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды