APRILIA RSV4 R Скачать руководство пользователя страница 160

Страница: 160 / 475

cated by the diagnosis instrument: if the voltage does not vary, there is a short circuit in the

cable wiring; replace the throttle grip sensor if the voltage drops to zero.

•

if the circuit is open, shorted to negative: check the throttle grip sensor connector and the

Marelli control unit connector. If not OK, restore. If OK, check circuit continuity between the

two cable terminals. If not OK, restore; if OK, check the cable ground insulation (from the

throttle grip sensor connector or the control unit connector): if the cable is not ground insu-

lated, restore the wiring. If it is ground insulated, and with the switch key set to ON, check

that there is power supply for the potentiometer PIN D and that PIN F is connected to ground.

If both are correct, replace the throttle grip sensor; if not, check the continuity of the cable

that is not functioning properly: if there is continuity, replace the control unit; if not, restore

the wiring

DIAGNOSIS INSTRUMENT: LOGIC ERRORS

Blue lower connector throttle grip position (tracks A-B) P0154

•

incongruent signal

Error cause

•

Two illogical voltage signals have been detected at PIN 13 and 39 of the ENGINE connector

(tracks A-B)

Troubleshooting

•

Check the parameters of the blue lower connector Throttle Grip Position Sensor - tracks A

and B: if one of the two values clearly deviates from 600-1400 mV, it means that this po-

tentiometer is defective. Check the throttle grip sensor connector and the control unit

connector: if not OK, restore. If OK, check that cable resistance between the throttle grip

sensor connector and the control unit is a few tenths of Ohm: if this is not the case, restore

wiring. If the value is correct, replace the complete throttle grip sensor

White upper connector throttle grip position (tracks C-D) P0155

•

incongruent signal

Error cause

•

Two illogical voltage signals have been detected at PIN 23 and 11 of the ENGINE connector

(tracks A-B)

Troubleshooting

•

Check the parameters of the white upper connector Throttle Grip Position Sensor - tracks

C and D: if one of the two values clearly deviates from 600-1400 mV, it means that this

potentiometer is defective. Check the throttle grip sensor connector and the control unit

connector: if not OK, restore. If OK, check that cable resistance between the throttle grip

sensor connector and the control unit is a few tenths of Ohm: if this is not the case, restore

wiring. If the value is correct, replace the complete throttle grip sensor

Throttle grip position P0156

Electrical system

RSV4 R

ELE SYS - 160

Содержание RSV4 R




























































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды

APRILIA RSV4 R, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 R

Отзывы:

Похожие инструкции для RSV4 R

Бренды по названию

Популярные бренды