APRILIA Caponord 1200 2016 Скачать руководство пользователя

Страница: 246 / 573

•

Excessive voltage is found or null voltage between sensor connector PIN 2 and VCU PIN

D1.

Troubleshooting

•

Disconnect the sensor connector and check PIN 2 ground and power insulation. if insulation

is not present, restore the cable harness; otherwise replace the sensor.

•

Check that sensor connector PIN 2 is insulated from both ground (connector PIN 1) and

power (connector PIN 3) and also from connector PIN 4. Reconnect the VCU, turn the key

ON and check that there are 5V between connector PIN 1 and 3. If the checks return positive

results replace the sensor.

Recovery

•

None

Temperature sensor short circuit error C1410

Error cause

•

Circuit interruption detected

Troubleshooting

•

Check the component connector and the VCU connector. Disconnect the two connectors

and check for continuity of the cable between sensor PIN 2 and VCU PIN D1 and restore

the cable harness. If the cable harness is intact replace the sensor.

•

Check the continuity between sensor connector PIN 1 and VCU PIN F3. Check the continuity

between sensor connector PIN 2 and VCU PIN D1. Also check that there are 5V between

connector PIN 1 and 3. If the checks return positive results replace the sensor.

Recovery

•

None

Rotary sensor

(IF AVAILABLE)

Function

Find the swingarm position (the angle between the

swingarm and the frame).

Operation / Operating principle

The system, by means of the VCU (Vehicle Control

Unit), measures the energy transmitted to the Ca-

ponord 1200 in real time (shock absorber damp-

ing) by the bumps in the asphalt and adapts the

calibration of the suspension in real time in order

Electrical system

Caponord 1200 - Caponord 1200 Rally

ELE SYS - 246

Содержание Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды

APRILIA Caponord 1200 2016, Руководство пользователя

Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды