APRILIA Caponord 1200 2016 Скачать руководство пользователя страница 233

Страница: 233 / 573

•

If the potentiometer signal is out of threshold check for continuity between motor PIN 3 -

VCU PIN F3 and between motor PIN 2 - VCU PIN B4

•

If time is excessive: check the component connector and the VCU connector. Disconnect

the two connectors and check the continuity of the cable between motor PIN 4 - VCU PIN

L1 and between motor PIN 5 - VCU PIN L2. If all the above checks return a positive result

replace the motor.

•

If the search is not carried out, incorrect travel: carry out the acquisition procedure using the

diagnostics instrument.

Exhaust butterfly valve engine P0192

•

open circuit / short circuit to negative / short circuit to positive, short circuit between the two

cables

Error cause

•

If the circuit is open: circuit interruption detected. If shorted to negative: null voltage detected

on PIN L1 or on VCU PIN L2. If shorted to positive, short circuit between the two cables:

excessive voltage detected on PIN A1 or on VCU PIN L2.

Troubleshooting

•

If the circuit is open: check the component connector and the VCU connector. Disconnect

the two connectors and check the continuity of the cable between motor PIN 4 - VCU PIN

L1 and between motor PIN 5 - VCU PIN L2. If the cable harness is intact replace the com-

ponent.

•

If shorted to negative: disconnect the motor connector and check ground and PIN 4 and 5

insulation: if insulation is not present, restore the cable harness; otherwise replace the com-

ponent.

•

If shorted to positive, short circuit between the two cables: check the component connector

and the VCU connector. disconnect the component connector and check power and PIN 4

and 5 insulation; also check that the two PINs are insulated from one another. If all the above

checks return a positive result replace the component.

Exhaust butterfly valve potentiometer P0193

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at VCU PIN B4. If the circuit is

open, shorted to negative: null voltage has been detected at VCU PIN B4.

Troubleshooting

•

If shorted to positive: Disconnect the component connector and check power and PIN 2

insulation: if insulation is not present, restore the cable harness; otherwise replace the com-

ponent.

Caponord 1200 - Caponord 1200 Rally

Electrical system

ELE SYS - 233

Содержание Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Бренды по названию

Популярные бренды

APRILIA Caponord 1200 2016, Руководство пользователя

Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Бренды по названию

Популярные бренды