manualshive.com logo in svg

APRILIA Caponord 1200 2016, Руководство пользователя

Поделиться
Скачать
APRILIA Caponord 1200 2016 Скачать руководство пользователя страница 196

In closed loop, the value must be close to 1.00 (values not within the 0.90 - 1.10 interval indicate a fault):

for example, value 0.75 corresponds to +25% with respect to the reference injection time; 1.25 corre-

sponds to -25%. In an open circuit, the oxygen sensor signal is too low. Therefore, the control unit takes

it as a lean combustion condition and will try to enrich it. The value read will be 0.75: once this correction

has been tried, the value shifts to 1.00 fixed and the Lambda probe error is signalled.

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

DIAGNOSTICS INSTRUMENT: STATUSES

Lambda probe: Start-up_Lean_Rich_Fault due to rich value_Fault due to lean value

•

If the probe connector is removed (voltage almost equal to zero), the status is Fault due to

lean value.

Lambda check: Open loop/Closed loop/Rich in closed loop/Lean in closed loop/enriched

•

Closed loop indicates that the control unit is using the oxygen sensor signal to keep the

combustion as close as possible to the stoichiometric value.

DIAGNOSTICS INSTRUMENT: ACTIVATION

Lambda probe heating

•

The auxiliary injection relay (No. 46 in the wiring diagram, placed in the front relay box, left

side; CHECK, however, the identification of the relay with the colour of the cables) is ener-

gised and the heating circuit is closed to ground 5 times (pin 3 of the lambda probe

connector). The continuity of the wiring is necessary for correct activation: no error indica-

tions are displayed in case of lack of activation.

DIAGNOSTICS INSTRUMENT: ELECTRICAL ERRORS

Front lambda probe P0130

•

shorted to positive

Error cause

•

Excessive voltage (battery voltage) has been detected at PIN 10 and 22 of the ENGINE

connector. Caution: the 'Oxygen sensor' parameter is not the real value that is read; a re-

covery value is displayed instead. The instrument panel does not indicate the presence of

this error even in the ATT status.

Troubleshooting

•

shorted to positive: with key set to ON, disconnect the sensor connector and measure PIN

1 voltage on the cable harness side (grey cable): if there is voltage (5 or 12 V), restore the

cable harness; if there is not, replace the lambda probe.

Rear lambda probe P0136

Electrical system

Caponord 1200 - Caponord 1200 Rally

ELE SYS - 196

Содержание Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды