APRILIA Caponord 1200 2016 Скачать руководство пользователя

Страница: 212 / 573

Indicates whether the self-acquisition process through the diagnosis instrument has/has not been car-

ried out: if it has been carried out once, will always be carried out unless EEPROM control unit zero

setting is carried out

DIAGNOSIS INSTRUMENT: ELECTRICAL ERRORS

CAUTION

IF ERRORS ARE DETECTED ON BOTH THROTTLE BODIES, CHECK ALSO THE CORRECT SUP-
PLY OF THE CONTROL UNIT TO PIN 42.

potentiometer 1 sensor, front throttle position P0120

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 48. If the circuit is open,

shorted to negative: voltage equal to zero has been detected at PIN 48.

Troubleshooting

•

If shorted to positive: check the value shown by the parameter of the front throttle Potenti-

ometer 1 (voltage): disconnect the connector and read the value indicated by the diagnosis

instrument: if the voltage does not vary, there is a short circuit in the cable; replace the throttle

body if the voltage drops to zero

•

If the circuit is open, shorted to negative: check the throttle body connector and the control

unit connector. If not OK, restore; if everything is OK, check circuit continuity between the

two terminals. If not OK, restore the cable harness; if OK, check the circuit ground insulation

(from throttle sensor connector or control unit connector). If it is ground insulated, check that

there is power (+5 V) at the throttle body connector PIN 2, and that PIN 6 is connected to

ground. If both are correct, replace the throttle body

potentiometer 2 sensor, front throttle position P0122

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 50. If the circuit is open,

shorted to negative: voltage equal to zero has been detected at PIN 50.

Troubleshooting

•

If shorted to positive: check the value shown by the parameter of the front throttle Potenti-

ometer 2 (voltage): disconnect the connector and read the value indicated by the diagnosis

instrument: if the voltage does not vary, there is a short circuit in the cable; replace the throttle

body if the voltage drops to zero

•

If the circuit is open, shorted to negative: check the throttle body connector and the control

unit connector. If not OK, restore; if everything is OK, check circuit continuity between the

two terminals. If not OK, restore the cable harness; if OK, check the circuit ground insulation

(from throttle sensor connector or control unit connector). If it is ground insulated, check that

Electrical system

Caponord 1200 - Caponord 1200 Rally

ELE SYS - 212

Содержание Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды

APRILIA Caponord 1200 2016, Руководство пользователя

Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды