APRILIA Caponord 1200 2016 Скачать руководство пользователя страница 230

Страница: 230 / 573

•

The search for the opening travel limit (valve open) and the closing travel limit (valve closed)

is carried out. During both normal operation and the self-cleaning cycle, the valve will only

move within this range and without reaching the mechanical end stops, to prevent strain to

the electric motor.

(Caponord 1200)

DIAGNOSTICS INSTRUMENT: LOGIC ERRORS

Exhaust butterfly valve position P0190

•

position error.

Error cause

•

Position indicated by potentiometer does not correspond with position set by control unit.

Troubleshooting

•

Mechanically check the valve, its normal rotation (with cables disconnected from motor,

manually activate the cables and see movement regularity and check valve complete stroke

with correct operation of the return spring) and absence of foreign bodies which do not allow

its rotation: if not OK, restore; if OK, check valve and instrument panel connectors (special

attention to oxidation) and check cables resistance: if not OK, restore; if OK, always with

cables disconnected and key set to ON, check normal rotation of the electric motor and

replace motor (potentiometer does not work correctly).

DIAGNOSTICS INSTRUMENT: ADJUSTABLE PARAMETERS

•

Acquire exhaust butterfly valve zero position.

NOTE: Motor is placed in a reference position to correctly search mechanical stop later.

•

Exhaust butterfly valve self-acquisition

NOTE: Search minimum and maximum mechanical stop.

DIAGNOSTICS INSTRUMENT: ELECTRICAL ERRORS

Exhaust butterfly valve stop search P0191

•

excessive time / search not carried out, incorrect travel / potentiometer signal above MAX

threshold and under MIN threshold

Error cause

•

If search not carried out. Carry out travel stop search.

•

If time is excessive: failure to memorise valve stop positions. The EVC is unable to record

the valve stops: probable circuit interruption. If the search is not carried out, incorrect travel:

memorisation of valve stop positions absent: this occurs at the first start of the bike or fol-

lowing a control unit reset.

•

If incorrect travel, carry out reset, cable adjustment and stop search again.

Troubleshooting

Electrical system

Caponord 1200 - Caponord 1200 Rally

ELE SYS - 230

Содержание Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Бренды по названию

Популярные бренды

APRILIA Caponord 1200 2016, Руководство пользователя

Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Бренды по названию

Популярные бренды