APRILIA Caponord 1200 2016 Скачать руководство пользователя

Страница: 192 / 573

•

If the circuit is open, shorted to positive: excessive voltage has been detected at PIN 12 of

the ENGINE connector. If shorted to negative: voltage equal to zero has been detected. The

instrument panel does not indicate the presence of this error even in the ATT status.

Troubleshooting

•

If the circuit is open, shorted to positive: check the sensor connector and the Marelli control

unit connector. If they are OK, check sensor continuity: replace the sensor if not OK; if OK,

check continuity between the ENGINE connector PIN 12 and the sensor PIN 1: restore cable

harness if there is not continuity; if it is OK, reconnect the control unit connector and, with

key set to key ON, check the continuity between the sensor connector PIN 2 and the vehicle

ground connection: if OK, it means that the error cause is that the cable is shorted to positive

and it is necessary to restore the cable harness between ENGINE PIN 12 and sensor PIN

1; if there is no continuity with the ground connection, check the sensor connector and the

Marelli control unit connector. If not OK, restore the cable harness. If OK, check continuity

between the ENGINE connector PIN 6 or 17 and the sensor connector PIN 2: restore the

cable harness if there is not continuity. If there is, it means that the control unit does not

supply the ground connection and therefore should be replaced.

•

If shorted to negative, check sensor correct resistance: if resistance is null, replace the sen-

sor; if resistance is correct, it means that the Yellow/Brown cable has ground connection:

restore the cable harness

DIAGNOSTICS INSTRUMENT: LOGIC ERRORS

engine temperature sensor P0116

•

signal not valid.

Error cause

•

An excessive temperature variation has been detected: for example, the cause may be a

contact resistance between the terminals. The instrument panel does not indicate the pres-

ence of this error even in the ATT status.

Troubleshooting

•

Check the sensor connector and the ENGINE connector of the Marelli control unit.

NOTES

No error is detected if the sensor does not work correctly or the control unit connector or sensor terminals

are rusty: then use the diagnostics instrument to check if the temperature indicated is the same as the

engine temperature. Check also that the sensor electrical characteristics are observed: replace the

sensor if not OK; if it is OK, check the sensor connector and the Marelli control unit connector.

Electrical system

Caponord 1200 - Caponord 1200 Rally

ELE SYS - 192

Содержание Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды

APRILIA Caponord 1200 2016, Руководство пользователя

Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды