APRILIA Caponord 1200 2016 Скачать руководство пользователя

Страница: 174 / 573

•

If too high: check correct operation of the voltage regulator.

•

If too low: check voltage regulator connectors, engine - vehicle cable harness connector and

the control unit connector (paying special attention to possible oxidation): if not OK, restore;

if OK, check that Red/White cable resistance from the voltage regulator connector to the

control unit connector is a few tenths of Ohm: if not OK, restore cable harness; if OK, check

correct operation of the electrical alternator: if not OK, restore; if OK, check operation of the

voltage regulator

VCU ERRORS

Battery tension too low or too high C1001

Error cause

•

The battery tension is below the minimum threshold (6 V with engine on, 10 V with engine

off) or above the maximum threshold (16 V).

Troubleshooting

•

Check the battery.

Speed sensor

VEHICLE FRONT SPEED SENSOR

FUNCTION:

To indicate the vehicle speed by read-

ing the front wheel turning speed.

OPERATION / OPERATING PRINCIPLE:

Magne-

toresistive sensor: a square-wave pulse is gener-

ated with voltage approx. between 11.55 V and

11.25 V

WIRING DIAGRAM

Level in wiring diagram: ABS.

REMOVAL

LOCATION ON THE VEHICLE:

on the fork, right

stem, next to the brake calliper support.

CONNECTOR LOCATION (if available):

under

the helmet compartment.

PINS

•

PIN 1- Ground connection (white)

•

PIN 2 - Power supply voltage/Output

signal (white/brown)

DIAGNOSIS INSTRUMENT

Parameters:

Speed (km/h) - Vehicle speed.

ELECTRICAL ERRORS

Speed sensor

Electrical system

Caponord 1200 - Caponord 1200 Rally

ELE SYS - 174

Содержание Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды

APRILIA Caponord 1200 2016, Руководство пользователя

Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды