APRILIA Caponord 1200 2016 Скачать руководство пользователя

Страница: 10 / 573

Maintenance rules

GENERAL PRECAUTIONS AND INFORMATION

When repairs, disassembly and reassembly of the vehicle is carried out, follow the following recom-

mendations strictly.

BEFORE DISASSEMBLING COMPONENTS

•

Remove the dirt, mud, dust and foreign objects from the vehicle before disassembling com-

ponents. Wherever required, use the special tools designed for this vehicle.

DISASSEMBLING COMPONENTS

•

Do not loosen and/or tighten the screws and nuts using pliers or other tools, but always use

the specific wrench.

•

Mark the positions on all the connection joints (hoses, cables, etc.) before separating them

and identify them with different distinctive marks.

•

Each piece should be clearly marked in order to be identified during the installation phase.

•

Carefully clean and wash the disassembled components with detergents with a low flam-

mability grade.

•

Keep the coupled parts together because they have "adapted" to one another following

normal wear.

•

Some components must be used together or replaced entirely.

•

Keep away from heat sources.

REASSEMBLING COMPONENTS

CAUTION

BEARINGS MUST ROTATE FREELY, WITHOUT JAMMING AND/OR NOISE, OTHERWISE, THEY
NEED TO BE REPLACED.

•

Only use ORIGINAL Aprilia SPARE PARTS.

•

Comply with lubricant and consumables use guidelines.

•

Lubricate parts (whenever possible) before reassembling them.

•

When tightening nuts and screws, start either from the components with the largest diameter

or from the innermost components, proceeding diagonally. Tighten nuts and screws in suc-

cessive steps before applying the tightening torque.

•

Always replace self-locking nuts, washers, sealing rings, circlips, O-rings (OR), cotter pins

and screws with new parts if the thread is damaged.

•

When assembling the bearings, make sure to lubricate them well.

•

Check that each component is assembled correctly.

•

After a repair or routine maintenance, carry out pre-ride checks and test the vehicle on

private grounds or in an area with low traffic.

Characteristics

Caponord 1200 - Caponord 1200 Rally

CHAR - 10

Содержание Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды

APRILIA Caponord 1200 2016, Руководство пользователя

Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды