APRILIA Caponord 1200 2016 Скачать руководство пользователя страница 155

Страница: 155 / 573

ESISTANCE

MEASUREMENT

Winding stage

Ambient temperature (ohm)

Afterwards heat stabilisation (ohm)

Stage 1

0.15 - 0.20

0.18 - 0.23

Stage 2

0.15 - 0.20

0.18 - 0.23

Stage 3

0.15 - 0.20

0.18 - 0.23

Zero load voltage

•

Disconnect the three-way connector (1);

•

For a correct detection of the alternator voltage, a measurement must be carried out using

alternatively the 3 engine side connector pins: stage "1" (pin 1-2), stage "2" (pin 1-3), stage

"3" (pin 2-3)

•

Take the measurements;

•

If there is a significant difference between one stage and another (other than 15 V), this

means that the alternator is defective and must be replaced.

CAUTION

WITH THE ENGINE HOT THE VALUES RECORDED ARE ON AVERAGE 4-5 V LESS THAN THOSE
DETECTED WITH THE ENGINE COLD.

MPTY

VOLTAGE

rpm

2000

6000

8000

Vm linked voltage Reference values (V rms)

20 - 30

75 - 85

95 - 105

Short-circuit current

•

For a correct detection of the short-cir-

cuit current, a connector must be pre-

pared that generates a downstream

short circuit between the three alterna-

tor cables;

•

Start the engine and with an ammeter

clamp measure each single cable.

•

If there is a significant difference be-

tween the measure of the single cables

(other than 10 A), this means that the

alternator is defective and must be re-

placed.

CAUTION

WITH THE ENGINE HOT THE VALUES RECORDED ARE
ON AVERAGE 2-3 A LESS THAN THOSE DETECTED WITH
THE ENGINE COLD.

WARNING

NEVER KEEP THE ENGINE RUNNING FOR MORE THAN
ONE MINUTE; FAILURE TO DO SO COULD CAUSE SERI-
OUS OVERHEATING DAMAGES TO THE MOTORCYCLE
CIRCUITS.

Caponord 1200 - Caponord 1200 Rally

Electrical system

ELE SYS - 155

Содержание Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Бренды по названию

Популярные бренды

APRILIA Caponord 1200 2016, Руководство пользователя

Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Бренды по названию

Популярные бренды