manualshive.com logo in svg

APRILIA Caponord 1200 2016, Руководство пользователя

Поделиться
Скачать
APRILIA Caponord 1200 2016 Скачать руководство пользователя страница 182

•

Example value with key ON: 0 mV

•

Example value with engine on: -

With a released throttle grip, the value read should be 0%, whereas 100 % should be read with throttle

grip fully twisted.

DIAGNOSIS INSTRUMENT: STATUSES

Throttle grip

•

Slightly twisted_choked_fully twisted

Handle self-learning

•

carried out/not carried out

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

DIAGNOSTICS INSTRUMENT: ELECTRICAL ERRORS

Blue front connector throttle grip position sensor - track A P0150

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 39 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 39 of the ENGINE connector.

Troubleshooting

•

shorted to positive: check the value shown by the parameter of the BLUE front connector

Throttle Grip Position Sensor - track A: disconnect the connector and read the value indi-

cated by the diagnostics instrument: if the voltage does not vary, there is a short circuit in

the cable wiring; replace the throttle grip sensor if the voltage drops to zero.

•

if the circuit is open, shorted to negative: check the throttle grip sensor connector and the

Marelli control unit connector. If not OK, restore. If OK, check circuit continuity between the

two cable terminals. If not OK, restore; if OK, check the cable ground insulation (from the

throttle grip sensor connector or the control unit connector): if the cable is not ground insu-

lated, restore the wiring. If it is ground insulated, and with the key set to ON, check that there

is power supply for the potentiometer PIN A and that PIN C is connected to ground. If both

are correct, replace the throttle grip sensor; if not, check the continuity of the cable that is

not functioning properly: if there is continuity, replace the control unit; if not, restore the wiring

Blue front connector throttle grip position sensor - track B P0151

•

short circuit to positive / open circuit, short circuit to negative

Error cause

Electrical system

Caponord 1200 - Caponord 1200 Rally

ELE SYS - 182

Содержание Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды