APARIAN A-DNP3R Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 108

background image

Diagnostics

Document No. D109-010

Page 79 of 108

Revision 1.15

7.

DIAGNOSTICS

7.1.

LEDS

The module provides three LEDs for diagnostics purposes as shown in the front view figure
below. A description of each LED is given in the table below.

Figure 7.1 - DNP3 Router front view

LED

Description

Ok

The module’s Ok LED will provide information regarding the system-level operation of
the module. Thus if the LED is red then the module is not operating correctly. For
example if the module application firmware has been corrupted or there is a hardware
fault the module will have a red Module LED.

If the LED is green then the module has booted and is running correctly.

Act

The activity LED is used for the RS232 serial port. Every time there is a successful DNP3
routing transaction the LED will flash green. The LED will flash red if the routing was
unsuccessful (e.g. failed checksum).

Eth

The Ethernet LED will light up when an Ethernet link has been detected (by plugging in
a connected Ethernet cable). The LED will flash every time traffic was detected.

Table 7.1 - Module LED operation

«
...
77
78
79
80
81
...
»

Содержание A-DNP3R













































































































Отзывы:

Нет отзывов

Похожие инструкции для A-DNP3R

Бренд: Parkside Страницы: 55

Бренд: Parkside Страницы: 34

Бренд: X-Micro Страницы: 74

Бренд: Zhone Страницы: 7

Бренд: Zhone Страницы: 1

Бренд: Abocom Страницы: 2

UniFi Cloud Key

Бренд: Ubiquiti Страницы: 13

Бренд: H3C Страницы: 4

Бренд: National Instruments Страницы: 80

Бренд: Airvana Страницы: 90

Acme Packet 3900

Бренд: Oracle Страницы: 70

Бренд: ALIBI Страницы: 232

Redbooks Emulex VFA5

Бренд: IBM Страницы: 15

Бренд: Alcatel Страницы: 158

Бренд: Ultra Страницы: 4

Бренд: Trane Страницы: 8

Бренд: Datacom Страницы: 118

Бренд: NETGEAR Страницы: 232

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды