Anritsu MX183000A Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 226

Anritsu MX183000A Скачать руководство пользователя страница 9

ix

Protection Against Computer Virus Infections

Prior to the software installation
Before installing this software or any other software recommended or
approved by Anritsu, run a virus scan on your computer, including
removable media (e.g. USB memory stick and CF memory card) you
want to connect to your computer.

When using this software and connecting with the measuring instrument

•

Copying files and data

On your computer, do not save any copies other than the following:

•

Files and data provided by Anritsu

•

Files created by this software

•

Files specified in this document

Before copying these files and/or data, run a virus scan, including
removable media (e.g. USB memory stick and CF memory card).

•

Connecting to network

Connect your computer to the network that provides adequate
protection against computer viruses.

Cautions on Proper Operation of Software

This software may not operate normally if any of the following operations
are performed on your computer:

•

Simultaneously running any software other than that recommended or

approved by Anritsu

•

Closing the lid (Laptop computer)

•

Turning on the screen saver function

•

Turning on the battery-power saving function (Laptop computer)

For how to turn off the functions, refer to the operation manual that came
with your computer.

«
...
7
8
9
10
11
...
»

Содержание MX183000A



































































































































































































































Отзывы:

Нет отзывов