Anritsu MX183000A Скачать руководство пользователя страница 86

Страница: 86 / 226

Chapter 4 Operation

4-32

Table 4.6.2-1 JTOL Settings Items

Item

Description

Detection

Unit

Sets whether error rate or error count is used for pass/fail

judgment.
Error Rate: Judges using error rate.
Error Count: Judges using error bit count. (default)
Estimate:

Judges using error rate.

Measures jitter tolerance using the error rate determined from

the Direction Search setting such as 1E–6 as the target. The

measurement results from this process are used to estimate

the jitter tolerance for the value specified by BER for JTOL

Estimation.

Note:

A BER for a rate lower than the intermediate measurement

is estimated even using the Error Rate/Count Rate setting,

but estimation may not be possible for certain intermediate

results. Setting to Estimate allows BER to be estimated

reliably.

For details, refer to Section 4.7.3 “Jitter Tolerance

Estimate”.

Error Count/

Error Threshold

Sets the threshold for judgment using the judgment method

selected in Unit. The judgment will be Fail if the bit error

value exceeds the threshold.
When Unit is set to Error Rate:

1E–3 to E–12 1E–1 Step (Default: 1E–12)
When Unit is set to Error Count: 0 to 10000000/Step 1

(default: 2)
When Unit is set to Estimate: Cannot be changed.

BER for JTOL

Estimation

The error rate used for Estimate can be changed. The results

will be refreshed even if this value is changed after the Jitter

Tolerance Test.

Содержание MX183000A



































































































































































































































Результаты поиска

Содержание MX183000A

Отзывы:

Anritsu MX183000A, Руководство по эксплуатации, Страница: 86 / 226

Результаты поиска

Содержание MX183000A

Отзывы: