Anritsu MX183000A Скачать руководство пользователя страница 117

Страница: 117 / 226

5.3 Command Description Method

5-11

em
ot

e C
on

trol

The following shows the description example of command.

■

Example of program command

:DISPlay:MEASure:CHANge <type>

Parameter

<type>=<CHARACTER PROGRAM DATA>
SETTing

Setting screen

RESult

Result screen

REPort

Report screen

Function

Switches the display screen for Tolerance/Sweep measurement.

Result cannot be specified for measurement not executed.

Example

Displays the Result screen for Tolerance measurement.

> :DISPlay:MEASure:CHANge RES

Program command

Parameter type name

Parameter type

Parameter contents

Command example

■

Example of query command

:SENSe:MEASure:SYSCond:SJSelect?

Response

<type>=<CHARACTER RESPONSE DATA>
OFF,SJ,SJ2

Function

Queries the sine wave jitter setting fixed and added for
Tolerance/Sweep measurement.

Example

> :SENSe:MEASure:SYSCond:SJSelect?
< SJ2

Command example, response example

Program command

Parameter type name

Parameter type

The < and > in the example indicate the response and the program
message respectively.

Notes:

●

Any commands for MX183000A are sequential commands.

●

If commands have restrictions, other settings may be affected.

For the setting items to be affected and conditions to be
restricted, refer to the

MX180000A Signal Quality Analyzer

Control Software Operation Manual and operation manual for
each module.

●

When the parameters of program command and query

command are same, the parameter of query command may be
omitted.

Содержание MX183000A



































































































































































































































Результаты поиска

Содержание MX183000A

Отзывы:

Anritsu MX183000A, Руководство по эксплуатации, Страница: 117 / 226

Результаты поиска

Содержание MX183000A

Отзывы: