Anritsu MX183000A Скачать руководство пользователя страница 76

Страница: 76 / 226

Chapter 4 Operation

4-22

Table 4.5.2-1 USB Link Sequence Setting Items

Item

Description

USB3.1 Specification

Selects and sets the USB specification from Gen1(5.0

GT/s) and Gen2(10.0 GT/s).
If MU181000A/B is installed, set the 32G PPG

Operation Bitrate to Gen1:5.0 GT/s and Gen2:10 GT/s

respectively.
Altering this item changes the sequence displayed in

Sequence Editor.

Test Pattern

Selects the test pattern output repeatedly from

Compliance or USER after completing the link training

sequence transmission.
Selecting Compliance displays the USB standard test

pattern selection controller. Selecting USER

automatically sets a test pattern specified for 32G PPG

on the MX180000A.
If Compliance is set, the pattern is set automatically in

accordance with 32G PPG.*
Selectable value changes depending on the value set for

USB 3.1 Specification.

Transmit/Stop

Starts sending a pattern selected at Test Pattern.
The button display is changed to Stop while the pattern

is sent.
When Stop is clicked, sending the pattern is stopped.
When Sequence Start is clicked, sending the pattern is

stopped automatically. The button display is changed to

Transmit.

Add Single Bit Error

Inserts a 1-bit error to the sending pattern.

This function is enabled in one of the following

conditions.

•

Gen1(5.0 GT/s), Compliance, CP0

•

Gen2(10.0 GT/s), Compliance, CP9

TS Option

Enables the setting screen display and setting status for

the USB Link Sequence in Figure 4.5.2-2to be altered.

*: Selecting CP5 or CP6 does not change de-emphasis setting that is

actually output.

Содержание MX183000A



































































































































































































































Результаты поиска

Содержание MX183000A

Отзывы:

Anritsu MX183000A, Руководство по эксплуатации, Страница: 76 / 226

Результаты поиска

Содержание MX183000A

Отзывы: