CNC Setup Utility Manual
P/N 70000490C - Index
All rights reserved. Subject to change without notice
Index-9
10-December-04
MC_2332, U friction feedfwd. timecons
(.1ms), 2-36
MC_2333, U damping feedfwd. at Nnom
(mA), 2-36
MC_2334, U torque LP filter timecons (.1ms),
2-36
MC_2335, U torque notch filter freq. (.1Hz),
2-36
MC_2336, U torque notch filter damp. (.1dB),
2-36
MC_2350, U display resolution, 2-36, 2-74
MC_2351, U in-position tolerance range,
2-36, 2-75
MC_2352, U default feed rate, 2-37
MC_2353, U default rapid rate, 2-37, 2-76
MC_2354, U axis type, 2-37
MC_2355, U reset rotary at 360, 2-37
MC_2356, U synchronized to XYZ, 2-37
MC_2357, U M11/M10 clamp enable, 2-37
MC_2900, spindle motor encoder connector,
2-37
MC_2901, spindle PWM output connector,
2-37
MC_2902, spindle inverter type, 2-37
MC_2903, spindle motor type, 2-38
MC_2904, spindle position encoder
connection, 2-38
MC_2905, spindle position encoder sinewave
period, 2-38
MC_2906, spindle position encoder line
count, 2-38
MC_2908, spindle position encoder signal
type, 2-38
MC_2909, spindle position encoder phase,
2-39
MC_2913, spindle motor encoder phase,
2-39
MC_2914, spindle DC bus voltage, 2-39
MC_2915, spindle i
2
t guarding, 2-39
MC_2916, spindle commutation offset speed
(rpm), 2-39
MC_2917, spindle commutation offset angle
(deg), 2-39
MC_2918, spindle velocity filter, 2-39
MC_2920, spindle current control gain
N<Nom (mV/A), 2-40, 5-2
MC_2921, spindle current control gain
N>Nom (mV/A), 2-40
MC_2922, spindle vel. control prop. gain
(mAs/rev), 2-40, 5-7
MC_2923, spindle vel. control integral
timecons (.1ms), 2-40, 5-7, 5-8
MC_2924, spindle vel. control integral limit
(ms), 2-40
MC_2925, spindle vel. control diff. gain
(.1mAs
2
/rev), 2-40
MC_2926, spindle pos. control prop. gain
(1/min), 2-40, 5-10
MC_2927, spindle pos. control output limit
(rpm), 2-41
MC_2928, spindle velocity feedfwd. gain,
2-41, 5-10
MC_2929, spindle acceleration feedfwd. gain
(.1mAs
2
/rev), 2-41, 5-10
MC_2930, spindle coulomb friction feedfwd.
gain (mA), 2-41, 5-10
MC_2931, spindle torque offset (mA), 2-41
MC_2932, spindle friction feedfwd. timecons
(.1ms), 2-41
MC_2933, spindle damping feedfwd. at Nnom
(mA), 2-41
MC_2934, spindle torque LP filter timecons
(.1ms), 2-41
MC_2935, spindle torque notch filter freq.
(.1Hz), 2-41
MC_2936, spindle torque notch filter damp.
(.1dB), 2-41
MC_2937, spindle flux reduction begin (rpm),
2-42
MC_2938, spindle flux reduction end (rpm),
2-42
MC_2939, spindle flux change factor (%),
2-42
MC_2940, spindle slip change timecons (ms),
2-42
MC_2941, spindle ramp (ms), 2-42
MC_2942, analog spindle maximum motor
speed (rpm), 2-42
MC_2943, analog spindle motor phase, 2-43
MC_2944, analog spindle pos. control integral
gain, 2-43
MC_2945, analog spindle pos. control integral
limit, 2-43
MC_2960, spindle output, 2-76
MC_2961, low setting for M40 gear ranges,
2-43, 2-77
MC_2962, high setting for M40 gear ranges,
2-43, 2-77
MC_2963, low setting for M41 gear ranges,
2-43, 2-77
