Amada MU-100A Скачать руководство пользователя страница 75

Страница: 75 / 114

MU-100A

11. Timing Chart (1-axis Type)

11-14

(9) Tangential Mode “Force Measure Mode : TANG(3)”

When 0=Setup parameter of the function menu is set as follows:

Force Measure Mode setting: TANG(3)

Tang Measure Point setting: Weld(0)

13ms

1ms

2ms

3ms

2ms

20ms min.

After Weld Force measurement position

After Weld Force measurement

SV11 to 13 output

(Weld Start output)

ST-FORCE1 input

GOOD output(*4)

FINISH output(*4)

NG output(*4)

LEV-FORCE11 to 13 output(*5)

(*3)

(*1)

(*2)

Hold-Time(setting)

Weld-Time(setting)

Welding(power supply)

Force change

LEV-FORCE1 set force

Tangential Force set force

*1 When Self Hold Validity is set to Invalid(1), hold the ST-FORCE input until the

sequence moves to Weld-Time.

*2 Set the time longer than the total weld time of welding machine for Weld-Time.

*3 The output time of After Weld Time varies depending on settings of Force

Sampling and Force Average.

*4 The output time can be selected with Output Select Time.

*5 The output time can be selected with Level Select Time.

Содержание MU-100A



















































































































Результаты поиска

Содержание MU-100A

Отзывы:

Amada MU-100A, Руководство по эксплуатации, Страница: 75 / 114

Результаты поиска

Содержание MU-100A

Отзывы: