Amada MU-100A Скачать руководство пользователя страница 74

Страница: 74 / 114

MU-100A

11. Timing Chart (1-axis Type)

11-13

(8) Sample Hold 1 Mode “Force Measure Mode :

SH2(2)”

When 0=Setup parameter of the function menu is set as follows:

Force Measure Mode setting: SH2(2)

(*2)

2ms

3ms

(Measures the highest output point.)

(*1)

Highest output point

GOOD output(*3)

FINISH output(*3)

NG output(*3)

After Weld Force measurement

Welding(power supply)

LEV-FORCE11 to 13 output

Weld-Time(setting)

(Weld start output)

Force change

Tangential Force set force

LEV-FORCE1 set force

3ms

(*4)

After Weld Force

measurement position

Make sure that this
is below the set force.

*1 When After Weld Time measurement time exceeds Weld-Time depending on

settings of Force Sampling and Force Average, “-----” is displayed.

*2 Set the time longer than the total weld time of welding machine for Weld-Time.

*3 The output time can be selected with Output Select Time.

*4 The output time can be selected with Level Select Time.

*5 Since the Weld Start is output when the sequence reaches the Tangential Force

setting in this mode, simultaneous start is not performed in 2-axis type.

Содержание MU-100A



















































































































Результаты поиска

Содержание MU-100A

Отзывы:

Amada MU-100A, Руководство по эксплуатации, Страница: 74 / 114

Результаты поиска

Содержание MU-100A

Отзывы: