Amada MAWA-300B-00-00 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 168

Amada MAWA-300B-00-00 Скачать руководство пользователя страница 77

MAWA-300B

4. Explanation of Screens

4-14

However, the reference voltage waveform is only “Mes Value.”

(t) Env Wave regist

Resistance welding is performed on the Envelope waveform check screen (Refer to
“4. (4)

1

Envelope waveform check screen.”) and “Record” is pressed in the status

where the envelope waveform is created, the envelope waveform data is saved into
the condition No. parameter being set.

(u) Envelope waveform registration status display

It is displayed that the envelope waveform is registered in the condition No. being set.
After “Record” is pressed and the waveform is successfully saved, “OK” is displayed.
When it is unsuccessful, “NG” is displayed.    If the waveform is not saved, “NON” is
displayed.

(v) BACK

The Envelope waveform check screen is displayed.

(w) Monitor select

The Monitor select screen is displayed.

Waveform registration
status display

«
...
75
76
77
78
79
...
»

Содержание MAWA-300B-00-00









































































































































































Отзывы:

Нет отзывов