Amada MAWA-300B-00-00 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 168

Amada MAWA-300B-00-00 Скачать руководство пользователя страница 11

MAWA-300B

Notification of Risk Information

6

4

WARNING

Electric wiring

[Source of risk]

Input cable and input/output signal cable

[Contents of risk]

If the cover is deteriorated or damaged, the cable is directly
touched, or a metallic part touched with the cable is touched, an
electric shock may be caused.

[Protective measure]

Do not use a deteriorated or damaged cable or plug. Put a cable
cover on the moving part or part touched with the human body so
that the input cable or input/output signal cable may not be
damaged.

5

WARNING

Electric wiring

[Source of risk]

Output cable (torch cable and grounding cable)

[Contents of risk]

A large current flows and a high voltage of about 10 kV is applied
at a start of welding. If a cable with an insufficient capacity or a
cable with a low electric strength is used, a fire or electric shock
may be caused.

[Protective measure]

Use the dedicated torch cable or grounding cable dedicate as the
output cable.
Fix the cable connecting part securely. Do not extend torch-side
cable and workpiece-side cable unnecessarily. The cable length
should be 10 m or less.

6

WARNING

Gas piping

[Source of risk]

Gas cylinder

[Contents of risk]

If the gas cylinder is fallen down, the foot may be collapsed.

[Protective measure]

Fix the gas cylinder securely on the gas cylinder stand or a
structure such as a wall or pillar.

7

WARNING

Gas piping

[Source of risk]

Gas flow rate adjuster

[Contents of risk]

If an inappropriate gas flow rate adjuster is used for the gas
cylinder, explosion may be caused.

[Protective measure]

Entrust the specialist with the gas piping work.

«
...
9
10
11
12
13
...
»

Содержание MAWA-300B-00-00









































































































































































Отзывы:

Нет отзывов