manualshive.com logo in svg

Amada MAWA-300B-00-00, Руководство по эксплуатации, Страница: 121 / 168

Поделиться
Скачать
Amada MAWA-300B-00-00 Скачать руководство пользователя страница 121

MAWA-300B 

5. Welding 

5-13 

(6)-2-3. Fine weld operation 

The fine weld mode is applied when the initial current time FST (ms) on the Welding condition setting 
screen is set to 0 (ms) and the Fine Weld Mode on the Switch select screen (1/2) is set to “ON.” 

 

 

 
 

 

 
 
 
 
 
 
 
 
 
 
 

Touch start head 

Torch 

Workpiece 

Pre-flow 
argon gas 

Main 
welding 

Electrode touch 
sensor (OFF) 

Electrode touch 
sensor (ON) 

Torch follow-up 
part 

Argon gas 

After-flow 
argon gas 

Head is a standby state at 
the start position. 

Start signal ON: Head 
moves to workpiece 
surface from the standby 
position 
Pre-flow: Argon gas 
output ON 
After electrode and 
workpiece make contact, 
torch follow-up part 
moves up. After that, 
electrode touch sensor is 
turned ON. After that, 
Head stops. 

After Head stops, it 
moves up to the main 
welding position. 
After torch follow-up 
sensor moves down, 
electrode touch senor is 
turned OFF. 
After that, the main 
welding starts. While 
Head moves up, the 
main welding is done for 
the set time. 

Head stops at the main 
welding position. 
After-flow: Argon gas 
output ON 
Start signal OFF: Head 
returns to the standby 
position. 

Содержание MAWA-300B-00-00









































































































































































Отзывы:

Нет отзывов